Pumpable self-levelling mortar with normal setting for levelling and smoothing from 5 to 50 mm thickness of new or pre-existing surfaces. Specially designed for the laying of light and wooden floors.
Floor repairs in both new construction and refurbishment.
Levelling and smoothing of concrete, ceramic and natural stone floors.
It is suitable for heated floors. This product is only suitable for indoor use.
It comes in 25kg bags and is packed on a pallet of 50kg.
The substrate shall be sound, dry, free of dust, grease and other impurities that could hinder adhesion.
If necessary, the substrate shall be mechanically treated by mechanical abrasion or shot blasting.
This process is always necessary on ceramic or natural stone and similar substrates.
Any cracks or fissures in the screeds must be repaired beforehand with MR TRIX.
Pour the product into a bucket with 4 - 4.5 litres of clean water, stir and mix with a low-speed electric mixer until a homogeneous, lump-free, self-levelling mixture is obtained.
Allow to stand for at least 3 minutes and mix again lightly to start applying the product.
The amount of LEVELAND mixed at a time should be the amount necessary to be used within a maximum time span of 60 minutes (at 23°C).
Do not add more water than indicated to the product as this may cause settling of the mass and weaken the mechanical properties of the mortar.
Spread the material in a single layer between 5 and 50 mm thick using a levelling trowel. It is advisable to pass the spiked roller within the allowed open time to help release any trapped air.
LEVELAND is suitable for application by plaster pump. If more than one coat is applied on a dry surface, the substrate must be primed again as described in the substrate preparation.
Once the application has been completed, it must be protected from draughts, direct sunlight and excessive temperatures. For the application of parquet the recommended minimum thickness of LEVELAND is 5mm.
In case of urgent applications it is important to control the moisture content of the product by means of an electronic or carbide hygrometer.
Consumption is 1,9Kg per m2 and mm of thickness.
The material can be cleaned fresh under running water. After drying, mechanical means are required.
Characteristic Values
Granulometry:
Bulk density:
Bulk density in paste:
Hardened bulk density:
PH of the mixture:
Solid waste:
Aspect:
Colour:
Presentation:
Tariff heading:
<1,0 mm
1450 kg/m2
2250 kg/m2
2250 kg/m2
12 ± 1
100 %
fine dust
grey
25 kg bags
3824 50 90
Mixing water:
Thickness:
Performance:
Application temperature:
Workability time:
Setting time:
Passable:
Time to coat:
Field of work:
18% clean water
(4 to 4.5 litres per sack)
of 25kg)
5-50 mm
1.95 kg/mm/m² 1.95 kg/mm/m² 1.95 kg/mm/m² 1.95 kg/mm/m
Between 5ºC and 25ºC
60 min
525 min (23ºC)
24 hours (23ºC)
24 hour gluing.
PVC, parquet, resins, etc.
7 days.
Indoor only
Compressive strength (N/mm2)
Compressive strength (N/mm2)
Flexural strength (N/mm2)
Wear resistance
Adherence
Surface hardness
Impact resistance
Modulus of elasticity in bending
Retraction
Thermal conductivity
Reaction to fire
>12 (at 24h and 23ºC)
>25 (at 28 days)
>6 (at 28 days)
<9cm3/50cm2 (class A9)
>2,0 N/mm2 (class B2,0)
> 100 N/mm2 (class SH100)
> 14 N-m (class IR14)
< 10 kN/mm2 (class E10)
< 0,1mm/m
1.18-1.30 W/mK (tabulated value)
Class A1
For any information concerning safety issues in the use, handling, storage and disposal of chemical residues, users should refer to the most recent version of the MSDS. Empty containers must be disposed of in accordance with current legislation.
The shelf life of the material is 12 months from the date of manufacture, provided it is stored in a dry place and protected from the weather.
The instructions for use are based on our tests and knowledge and are not binding. They do not release the consumer from examining and checking the products for correct use. The liability of the company is limited to the value of the used goods.
Levelling of interior floors, by application of a normal hardening, heavy-duty, self-levelling cementitious plaster for thicknesses up to 40 mm. (Leveland 5-50). The substrates must be dry, solid, dust-free, sound, compact and possibly consolidated or primed with suitable products (such as Primer Dur or Ecopoxi Primer). The material shall have the following characteristics characteristics:
Density of the mixture (kg/m³): 2,250
PH of the mixture: ~12
Transitability: 24 h
Compressive strength (N/mm²): 25 (at 28 days)
Bending strength (N/mm²): 6.0 (at 28 days)
Wear resistance (method EN 13892-3): Class A9
Surface hardness: SH100
Impact resistance: Class IR14
Retraction < 0,5mm/m
Reaction to fire: Class A1
Thickness (mm): from 5 to 50
Consumption (kg/m²): 1.9 (per mm thickness)
